神马av_日韩第一页_免费精品一区_神马AV_神马久久久久久久久_日韩无码第一页_色哒哒_无码人妻熟妇av又粗又_国产69久久久欧美黑人A片_日韩欧美亚洲_无码第一页_神马午夜精品91_无码人妻熟妇av又粗,日韩免费人妻无码专区蜜桃,亚洲阿大香蕉,欧美亚洲男人天堂,国产无码精品一区二区,揉着我的奶从后面进去视频,免费全部黄A片免费播放软件,国产色中色,免费看的久久久久,天美传媒部在线观看,久久久久久亚洲综合,大香蕉日韩成人在线视频,久久无码潮喷A片无码高潮动漫,精品久久亚洲熟女,国产欧美精品aaaaa久久,直男国产飞机杯,我的公把我弄高潮了视频,免费的精品一区二区三区片,国产日韩欧美三级,亚州A级片,自拍偷拍亚洲porn,少妇水多A片太爽了,日本久操,成人午夜福利无码不卡视频,国产一区二区不卡亚洲涩情,日韩欧美亚洲综合久久,国产亚洲精品久久孕妇呦呦你懂,国产又粗又长又大精品A片,自偷自拍亚洲综合精品第一页,亚洲欧美熟妇久久久久久久久 ,香蕉视频操逼奶子

The undercut and four corners of the ventilation pipe need to be sealed with sealant. In addition, the sealing surface of the vent pipe joint should be set on the positive pressure side of the vent pipe wall.

在風管加工過程中，通風管道不能設置加強框架或加強筋，因為這會對通風管道的質量產生一定的影響。

In the process of air duct processing, the ventilation duct can not be set with reinforcing frame or rib, because it will have a certain impact on the quality of the ventilation duct.

風管加工不能采用“S”形切割和“C”形直角切割的連接方式。此外，一些特殊的通風管道不能堵塞。

S-shaped cutting and C-shaped right angle cutting can't be used in air duct processing. In addition, some special ventilation ducts should not be blocked.

濟南通風管道

Jinan ventilation pipe

1、風管的制造和安裝應按照設計圖紙、合同和相關技術標準進行。任何變更一定要附有設計或合同變更通知或技術批準簽證。

1. The manufacture and installation of air duct shall be in accordance with the design drawings, contract and relevant technical standards. Any change must be accompanied by design or contract change notice or technical approval visa.

2、風管系統施工前，施工單位應與建設單位、監理單位、總承包商和設計單位進行協調。檢查風管及其他管道的位置和方向，檢查預留孔的安裝。施工應與土建工程和其他工種相協調。

2. Before the construction of air duct system, the construction unit shall coordinate with the construction unit, supervision unit, general contractor and design unit. Check the position and direction of air duct and other pipes, and check the installation of reserved holes. Construction shall be coordinated with civil engineering and other types of work.

3、風管生產安裝中使用的板材、型材等主要成品應符合設計及相關產品國家現行標準，濟南通風管道并有出廠檢驗證書。材料進場應按現行國家相關標準進行驗收。

3. The main finished products such as plates and profiles used in the production and installation of air duct shall meet the current national standards for design and related products, and Jinan ventilation duct shall have factory inspection certificate. Materials entering the site shall be accepted according to the current national standards.

4、當風管與風機連接時，應在進出風口處加軟接頭，其軟接頭的斷面尺寸應與風機進出風口一致。軟管接頭一般可采用帆布、人造革等材料，軟管長度不宜小于200，松緊度應適宜，柔性軟管可緩沖風機的振動。

4. When the air duct is connected with the fan, a soft joint shall be added at the air inlet and outlet, and the section size of the soft joint shall be consistent with the air inlet and outlet of the fan. Generally, the hose joint can be made of canvas, artificial leather and other materials, the length of the hose should not be less than 200, the tightness should be appropriate, and the flexible hose can buffer the vibration of the fan.