神马av_日韩第一页_免费精品一区_神马AV_神马久久久久久久久_日韩无码第一页_色哒哒_无码人妻熟妇av又粗又_国产69久久久欧美黑人A片_日韩欧美亚洲_无码第一页_神马午夜精品91_无码人妻熟妇av又粗,日韩免费人妻无码专区蜜桃,亚洲阿大香蕉,欧美亚洲男人天堂,国产无码精品一区二区,揉着我的奶从后面进去视频,免费全部黄A片免费播放软件,国产色中色,免费看的久久久久,天美传媒部在线观看,久久久久久亚洲综合,大香蕉日韩成人在线视频,久久无码潮喷A片无码高潮动漫,精品久久亚洲熟女,国产欧美精品aaaaa久久,直男国产飞机杯,我的公把我弄高潮了视频,免费的精品一区二区三区片,国产日韩欧美三级,亚州A级片,自拍偷拍亚洲porn,少妇水多A片太爽了,日本久操,成人午夜福利无码不卡视频,国产一区二区不卡亚洲涩情,日韩欧美亚洲综合久久,国产亚洲精品久久孕妇呦呦你懂,国产又粗又长又大精品A片,自偷自拍亚洲综合精品第一页,亚洲欧美熟妇久久久久久久久 ,香蕉视频操逼奶子

The expansion joint technology of ventilation pipeline is a non excavation local collar repair method. The main materials used in this technology are annular rubber water stop sealing belt and stainless ventilation pipe expansion joint. Rubber ring double expansion ring is installed at the pipe interface or local damaged part. After the ventilation pipe expansion joint is in place, it is fixed with 2-3 ventilation pipe expansion joints to achieve water stop. The expansion joint of the ventilation pipeline has fast construction speed, good quality stability, and can withstand interface dislocation. The anti internal pressure effect of the water stop collar is better than that of the external pressure, but it has an impact on the water flow pattern and the cross-section. In the non excavation of the drainage pipeline, it is usually used in combination with the drilling grouting method. The expansion joint of the ventilation pipe is mainly used for water leakage at the interface of the large-diameter pipe (the pipe diameter is not less than 800mm). The general process is as follows: according to the inner diameter of the pipe, first customize the stainless steel strip and rubber strip in the factory, and then enter the pipe for installation. First fix the rubber strip manually, and then press the expansion joint of the ventilation pipe with the sealing rubber ring through the pipe, so as to complete the local anti-seepage of the pipe. If necessary, grouting can be carried out for the leakage of the pipe.

通風管道伸縮節

Expansion joint of ventilation duct

安裝流程

Installation process

1.確定需要安裝通風管道伸縮節管段，在待管段上下游各一個檢查井內放置通風管道伸縮節保證待管段內臨時斷水；

1. It is determined that it is necessary to install the expansion joint of the ventilation pipe. The expansion joint of the ventilation pipe shall be placed in the inspection shaft at the upstream and downstream of the pipe section to ensure that the water supply in the pipe section to be temporarily cut off;

2.將管道內清洗干凈；

2. Clean the pipeline;

3.由于管徑DN800由工作人員直接進入管道確定位置；

3. Since the pipe diameter is DN800, the staff directly enter the pipeline to determine the position;

4.準備好通風管道伸縮節材料，先將環狀橡膠內襯于管道表面，再將通風管道伸縮節緊貼環狀橡膠使其固定管道表面工序結束后，確認漏水點全部止水；

4. Prepare the materials of the expansion joint of the ventilation pipe. First, put the annular rubber lining on the pipe surface, and then close the expansion joint of the ventilation pipe to the annular rubber to fix it on the pipe surface. After the process is completed, confirm that all the water leakage points are sealed;

5.TV內窺檢測（或人工拍照），確定管段后，是否已，作下記錄；

5. TV endoscope inspection (or manual photo taking) to determine whether the pipe section has been recorded;

6.路面恢復；

6. Pavement recovery;

通風管道伸縮節

Expansion joint of ventilation duct

7.整理竣工資料，備案。

7. Sort out the completion data and put it on record.

通風管道伸縮節使用要求：

Requirements for use of expansion joints of ventilation pipes:

（1）通風管道伸縮節設，首先要確定原管道的管道直徑，確保通風管道伸縮節外徑被管道的內徑之間的修正關系。

(1) When designing the expansion joint of the ventilation pipe, the pipe diameter of the original pipe shall be determined first to ensure the correction relationship between the outer diameter of the expansion joint of the ventilation pipe and the inner diameter of the pipe.

（2）采用通風管道伸縮節局部內襯法施工時，通風管道伸縮節的設計制作寬度滿足管段處的長度。

(2) When the local lining method of ventilation pipe expansion joint is adopted for construction, the design and fabrication width of ventilation pipe expansion joint shall meet the length of the pipe section.

（3）通風管道伸縮節與舊管道一起組成復合管道使用，內襯管設計壁厚滿足舊管道損壞地下水的滲漏壓力要求。

(3) The expansion joint of the ventilation pipe is used together with the old pipe to form a composite pipe. The design wall thickness of the inner liner pipe meets the leakage pressure requirements of the old pipe to damage the groundwater.

以上就是為大家介紹的有關濟南通風管道的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://m.xmxdgg.com

The above is the detailed introduction of Jinan ventilation duct. I hope it will help you. If you have any questions, please contact us. We will provide you with services with a professional attitude http://m.xmxdgg.com