神马av_日韩第一页_免费精品一区_神马AV_神马久久久久久久久_日韩无码第一页_色哒哒_无码人妻熟妇av又粗又_国产69久久久欧美黑人A片_日韩欧美亚洲_无码第一页_神马午夜精品91_无码人妻熟妇av又粗,日韩免费人妻无码专区蜜桃,亚洲阿大香蕉,欧美亚洲男人天堂,国产无码精品一区二区,揉着我的奶从后面进去视频,免费全部黄A片免费播放软件,国产色中色,免费看的久久久久,天美传媒部在线观看,久久久久久亚洲综合,大香蕉日韩成人在线视频,久久无码潮喷A片无码高潮动漫,精品久久亚洲熟女,国产欧美精品aaaaa久久,直男国产飞机杯,我的公把我弄高潮了视频,免费的精品一区二区三区片,国产日韩欧美三级,亚州A级片,自拍偷拍亚洲porn,少妇水多A片太爽了,日本久操,成人午夜福利无码不卡视频,国产一区二区不卡亚洲涩情,日韩欧美亚洲综合久久,国产亚洲精品久久孕妇呦呦你懂,国产又粗又长又大精品A片,自偷自拍亚洲综合精品第一页,亚洲欧美熟妇久久久久久久久 ,香蕉视频操逼奶子

The ventilation duct in the building is an important decoration to regulate the indoor air and temperature. It is matched with the fan, which is equivalent to the power source to input and discharge the air. It is found in Jiangsu ventilation duct that sometimes the fasteners of the fan will be loose when it runs for a long time. So what's going on? Let's have a look.

一旦風機的緊固件失效，就會對風機的運行產生一定是我影響，嚴重的還會損壞風機。因此，當風機在運行時就應該避免這種情況的發生。一般的，屋頂風機在常溫下運行時會有些溫度偏高的情況，不過都是在正常范圍之內，這是由于機器本身的零件相互摩擦，產生熱量導致機身溫度偏高，但并不是所有溫度過高的情況都是正常的。

Once the fastener of the fan fails, it will have a certain impact on the operation of the fan, and seriously damage the fan. Therefore, this situation should be avoided when the fan is running. Generally, when the roof fan operates at normal temperature, there will be some cases of high temperature, but they are all within the normal range. This is due to the high temperature of the fuselage caused by the friction between the parts of the machine itself, but not all cases of high temperature are normal.

實驗結果表明，導致屋頂風機緊固件失效的原因主要有以下幾點：1、運轉時，承受過大載荷量。就以軸流風機為例。由于它的運作時葉輪的輸出轉速快，因而，所要承受的載荷也就較大。一旦它的載荷超出的載荷范圍，其內部個零件也需將承擔一些載荷量，這就會造成零件緊固件失效。2、驟時開啟反轉。如果在風機還未完全停止時，突然開啟反轉，就會使風機的各個部件在受慣性的作用下，分別向不同的方向運行，使其個部件的運行不同步，從而導致風機出現問題。

The experimental results show that the main reasons for the failure of fasteners of roof fan are as follows: 1. Bear excessive load during operation. Take the fan shaft as an example. Because the output speed of the impeller is fast during its operation, the load to be borne is large. Once its load exceeds the load range, its internal parts also need to bear some load, which will cause the failure of part fasteners. 2. Turn on the reverse when suddenly. If the fan is suddenly turned on and reversed before it has completely stopped, each part of the fan will run in different directions under the action of inertia, making the operation of each part asynchronous, resulting in problems of the fan.

在發現風機出現緊固件松動現象時應該及時的進行處理，否則的話可能會導導致更大的問題發生。

In case of loose fasteners of the fan, it should be handled in time, otherwise it may lead to greater problems.